Characteristics of SKF Bearing
It can bear radial load and axial load at the same time. The higher the speed is, the greater the contact angle is, the higher the axial bearing capacity is.
Single row bearings can only bear axial load in one direction, which will cause additional axial force when bearing radial load. And can only limit the axial displacement of the shaft or housing in one direction. If it is installed in pairs, make the outer rings of a pair of bearings opposite, that is, the wide end face to the wide end face, and the narrow end face to the narrow end face. In this way, additional axial force can be avoided, and the shaft or housing can be limited to the axial clearance in both directions. There are more than 70 variant structures of angular contact ball bearings.
1. There are three kinds of nominal contact angles: 15 °, 25 ° and 40 °. The larger the contact angle is, the higher the axial bearing capacity is. High precision and high-speed bearings usually take 15 ° contact angle, which will increase under the action of axial force.
2. Generally, the inner ring or outer ring is provided with a locking port, and the inner and outer rings cannot be separated. After heating and expanding, the outer ring is assembled with the inner ring, rolling element and cage assembly. In the middle of the bearing groove, the bearing has more rigid balls and runs more smoothly than the rated ball.
3. The radial clearance can be adjusted by the mutual displacement of the inner and outer rings. It is often used in pairs and preloaded to improve the rigidity of the bearing. The characteristics of angular contact ball bearing can bear radial load and axial load at the same time. The higher the speed, the greater the contact angle, the higher the axial bearing capacity.
Single row bearings can only bear axial load in one direction, which will cause additional axial force when bearing radial load. And can only limit the axial displacement of the shaft or housing in one direction. If it is installed in pairs, make the outer rings of a pair of bearings opposite, that is, the wide end face to the wide end face, and the narrow end face to the narrow end face. In this way, additional axial force can be avoided, and the shaft or housing can be limited to the axial clearance in both directions. There are more than 70 variant structures of angular contact ball bearings.
1. There are three kinds of nominal contact angles: 15 °, 25 ° and 40 °. The larger the contact angle is, the higher the axial bearing capacity is. High precision and high-speed bearings usually take 15 ° contact angle, which will increase under the action of axial force.
2. Generally, the inner ring or outer ring is provided with a locking port, and the inner and outer rings cannot be separated. After heating and expanding, the outer ring is assembled with the inner ring, rolling element and cage assembly. The number of balls installed is more than that of deep groove ball bearing. The rated load is * * in the ball bearing, with strong rigidity and stable operation.
3. The radial clearance can be adjusted by the mutual displacement of the inner and outer rings. It is often used in pairs and preloaded to improve the rigidity of the bearing.
It can bear radial load and axial load at the same time. The higher the speed is, the greater the contact angle is, the higher the axial bearing capacity is.
Single row bearings can only bear axial load in one direction, which will cause additional axial force when bearing radial load. And can only limit the axial displacement of the shaft or housing in one direction. If it is installed in pairs, make the outer rings of a pair of bearings opposite, that is, the wide end face to the wide end face, and the narrow end face to the narrow end face. In this way, additional axial force can be avoided, and the shaft or housing can be limited to the axial clearance in both directions. There are more than 70 variant structures of angular contact ball bearings.
1. There are three kinds of nominal contact angles: 15 °, 25 ° and 40 °. The larger the contact angle is, the higher the axial bearing capacity is. High precision and high-speed bearings usually take 15 ° contact angle, which will increase under the action of axial force.
2. Generally, the inner ring or outer ring is provided with a locking port, and the inner and outer rings cannot be separated. After heating and expanding, the outer ring is assembled with the inner ring, rolling element and cage assembly. In the middle of the bearing groove, the bearing has more rigid balls and runs more smoothly than the rated ball.
3. The radial clearance can be adjusted by the mutual displacement of the inner and outer rings. It is often used in pairs and preloaded to improve the rigidity of the bearing. The characteristics of angular contact ball bearing can bear radial load and axial load at the same time. The higher the speed, the greater the contact angle, the higher the axial bearing capacity.
Single row bearings can only bear axial load in one direction, which will cause additional axial force when bearing radial load. And can only limit the axial displacement of the shaft or housing in one direction. If it is installed in pairs, make the outer rings of a pair of bearings opposite, that is, the wide end face to the wide end face, and the narrow end face to the narrow end face. In this way, additional axial force can be avoided, and the shaft or housing can be limited to the axial clearance in both directions. There are more than 70 variant structures of angular contact ball bearings.
1. There are three kinds of nominal contact angles: 15 °, 25 ° and 40 °. The larger the contact angle is, the higher the axial bearing capacity is. High precision and high-speed bearings usually take 15 ° contact angle, which will increase under the action of axial force.
2. Generally, the inner ring or outer ring is provided with a locking port, and the inner and outer rings cannot be separated. After heating and expanding, the outer ring is assembled with the inner ring, rolling element and cage assembly. The number of balls installed is more than that of deep groove ball bearing. The rated load is * * in the ball bearing, with strong rigidity and stable operation.
3. The radial clearance can be adjusted by the mutual displacement of the inner and outer rings. It is often used in pairs and preloaded to improve the rigidity of the bearing.
One-on-one service
Stock quickly
Experienced
Many successful cases
Online Service